Saturday 25/4/2015

Bookmark and Share
Case Studies
  PandCT RSS Case Studies feed
Less is more on high speed scribing machine

17 April 2007

An automated production systems designer has contained costs and enhanced reliability on his latest machine by using one of the key components to perform not one, but two critical functions.

Bob Jepp, founder and managing director of Robotix in Rugby has developed a high speed production line for scribing traceability serial numbers onto wheel rims for earthmoving equipment. This uses a single Hoerbiger-Origa rodless pneumatic cylinder in the dual critical roles of positioning the scribing head and holding the rim steady in the workstation. 

In use, wheel rims, which can vary in size from 24in dia and 15in wide to 40in by 40in, are delivered by a conveyor to the scribing workstation, where V-shaped guides position them accurately.

A large and powerful rodless cylinder mounted above the workstation descents, positions the scribing head just above the top surface of the rim to an accuracy of 0.01mm. Mounted on the cylinder and protruding beneath it is a pair of Hoerbiger-Origa’s linear shock absorbers; these contact the rim with sufficient force to hold the rim steady during scribing.

“We’ve used a 50mm bore cylinder which has enough power to hold the rim firmly in place,” explains Jepp. “The shock absorbers are there to prevent the cylinder from damaging the rims, and vice versa. They have to be stiff ones to transfer the holding force, and this means they will be reliable in the field too.

“The cylinder has, at 1000m, a relatively long stroke. This is to allow ease of access to the workstation by operators and maintenance engineers. It is fitted with one of Hoerbiger-Origa’s Starline Guides to ensure smooth and accurate motion in this arduous application”

The actions of the cylinder and other parts of the machine are controlled by a Mitsubishi PLC, the LCD display of which provides the operator with process and production messages.

The scribing head is a proprietary system from Technifor in Germany that uses a micro-percussion scribing drive and x-y configured servos for letter/numeral forming.

The scribing is fairly deep so that it can be easily read even in muddy working conditions, which means there are high forces being transmitted through the rims during scribing and hence Jepp’s decision to use one of Hoerbiger-Origa’s larger bore cylinders.

In fact all the pneumatic components, including valves, solenoids, air preparation equipment and secondary cylinders are sourced from Hoerbiger-Origa. Jepp explains the reason for this:

“Keeping the supplier count low is good for my build and management efficiency and also makes field servicing and maintenance easier. For operating reliability its makes sense to use the best equipment available, and when it comes to rodless pneumatic cylinders that means Hoerbiger-Origa.”

For more information, please contact:
Ray Barnes, Hoerbiger-Origa Limited
Unit 12, Brunel Court, Waterswell Business Park, Gloucestershire, GL2 2AL
Tel: 08700 600655. Email:
Website: are not responsible for the content of submitted or externally produced articles and images.
Click here to email PandCT about any errors or omissions contained within this article.
Send this page
To send this page to a colleague or friend,
fill in the email addresses below...
Your email address
Their email address:
Page to be sent: shownews.asp?ID=13994

Company gateway pages
for Parker Hannifin (Parker-Origa):
FREE Information on the products in this article
To request more information from this supplier,
fill in your email address below.
Your email address
Bookmark and Share
Product categories: Accelerometers | Actuators | Agitators | Analysers | Bearings | Compressors | Controllers | Conveyors | Drives | Enclosures | Flowmeters | Heat Exchangers | Motors | Pumps | Relays | Sensors | Transducers | Transmitters | Valves | Weighing
(c) Copyright 1999-2015 Process and Control Today Ltd  |  Reg. no 3733110  |  Email Editor  |  Email Webmaster  |  Sitemap  |  Privacy Policy