Saturday 25/10/2014

Bookmark and Share
 
 
Daily News
  PandCT RSS Daily News feed
European premiere: Omron presents Sysmac Automation Platform

9 December 2011

Omron celebrated the European premiere of its new automation platform at the SPS/IPC/DRIVES fair 2011: Sysmac (System for Machine Automation Control). Sysmac stands for one machine control through one controller, one software and one connection. On the occasion of the European launch, Shinya Yamasaki, Executive Officer & Senior General Manager of Omron Automation Systems Division Headquarters, Japan, came to visit the fair and to present the new automation platform.

Sysmac is a powerful and robust automation platform with a new machine automation controller (Sysmac NJ series), that integrates motion, sequencing, networking and machine vision, a new software (Sysmac Studio), that includes configuration, programming, simulation and monitoring and a fast machine network (EtherCAT) to control motion, vision, sensors and actuators. 

An immediate benefit of the new architecture is the seamless integration of Omron’s core competences within one control platform. Machine control and motion control are now one; field devices are controlled across one machine network and programmed by one software. 

One machine controller
The heart of the new automation platform is the Sysmac machine automation controller NJ series, which is designed for high speed and flexibility. It incorporates an Intel® processor proven for harsh industrial environments with fan-free operation and runs under an RTOS (real time operating system). It is scalable with a choice of 16, 32 and 64 axis CPUs. A response time of less than 1ms can be achieved for applications of up to 32 axes. Based on a microcontroller from Intel®, running under an RTOS, the Sysmac machine automation controller NJ series shifts from a rigid ASIC based architecture to a flexible and scalable software centric one.  

One machine software
Created to give machine builders full control over their automation system, Sysmac Studio integrates configuration, programming, simulation and monitoring into one software. A graphic-oriented configuration allows quick set-up of the controller, field devices and networks, while machine and motion programming based on IEC 61131-3 standard and PLCopen function blocks for motion control cuts programming time. Advanced simulation of sequence and motion control, data logging and data trace reduce machine tuning and set-up. 

One machine network
One connection via the Sysmac NJ series allows seamless control and communication with both the machine and the factory. The new NJ series is designed for open communication via EtherCAT, the fastest emerging network on the market for machine automation. It is simple to set-up and cost effective to install as it uses standard shielded Ethernet cables and connectors. EtherCAT is Omron’s de-facto machine network for its wide range of field and motion devices. Omron is also the first supplier offering vision sensors with an EtherCAT interface. 

Notes:
Intel is a trademark of Intel Corporation in the U.S. and/or other countries.
Sysmac is a trademark of Omron Corporation in Japan and/or other countries.


For further information, please contact:

Omron Electronics Ltd
, Opal Drive, Fox Milne, Milton Keynes, MK15 0DG Direct. +44 (0)1908 258254, Mob. +44 (0)7776 162 255 
Email jcommercial@eu.omron.com  www.industrial.omron.co.uk
PandCT.com are not responsible for the content of submitted or externally produced articles and images.
Click here to email PandCT about any errors or omissions contained within this article.
     
Send this page
To send this page to a colleague or friend,
fill in the email addresses below...
Your email address
Their email address:
Page to be sent: shownews.asp?ID=31324

Company gateway pages
for Omron Electronics Ltd:
FREE Information on the products in this article
To request more information,
fill in your email address below.
Your email address
 
     
Bookmark and Share
Product categories: Accelerometers | Actuators | Agitators | Analysers | Bearings | Compressors | Controllers | Conveyors | Drives | Enclosures | Flowmeters | Heat Exchangers | Motors | Pumps | Relays | Sensors | Transducers | Transmitters | Valves | Weighing
(c) Copyright 1999-2014 Process and Control Today Ltd  |  Reg. no 3733110  |  Email Editor  |  Email Webmaster  |  Sitemap  |  Privacy Policy