Wednesday 18/9/2019

Bookmark and Share
Case Studies
  PandCT RSS Case Studies feed

13 March 2013

Simplicity and reliability were among the key requirements for the custom control system developed and supplied by motor control expert, Ralspeed, for use on the UK’s largest slurry tank. The tank which, was designed, manufactured and installed by slurry handling specialist, Storth, is 40 m in diameter, almost 6 m high and is capable of holding over 7 million litres of slurry.

Slurry – which is essentially farm animal excrement mixed with water – is stored in the tank at certain times of year as an environmental protection measure, and then used on farmland at other times of year, where it acts as a valuable natural fertiliser that is rich in nitrates. Pumps are used to control the flow of slurry into and out of the tank, which is also equipped with motorised agitators to stir the slurry periodically during storage.

To provide the control system for the pump and agitator motors, Storth approached Ralspeed, a company with which had supplied efficient and dependable control systems for a number of earlier Storth projects.

For the new slurry tank, the design of the control system had to take into account the limited capacity of the mains supply at the tank installation site. This meant arrangements had to be made to limit the inrush current when starting the pumps and agitators, and also to ensure that no more than two agitators could run at the same time, and that the agitators could not run when the pumps are running.

Storth also wanted to be sure that the agitators had approximately equal usage, in order to equalise wear and tear, thereby maximising their operating lives. Further requirements were that the control system should be as simple as possible to facilitate maintenance, and that the user controls should be straightforward and intuitive.

To meet these special requirements, Ralspeed designed and built a fully customised control panel. The company used 18.5 kW Torq-master soft starters from its own range to control the motors. These units provide excellent control over the motor starting current, ensuring that the capacity of the supply is never exceeded, and also ensure that the agitators and pumps start and stop smoothly.

Because no more than two of the motors on the tank could ever be running simultaneously, the Ralspeed engineers realised that substantial cost savings could be achieved by using only two soft starters, and connecting them, via main contactors, to the appropriate motors as needed to meet operational requirements.

Ralspeed was able to provide a single selector switch to configure the operation of the system. This switch allows the user to rotate the duty of the agitators, and also to select operation of the pumps instead of the agitators when necessary. With careful design, it proved possible to implement this straightforward and effective form of control without needing to use a PLC or smart relay, thereby satisfying the end user’s request for simplicity.

For further information, please contact:

Debby Rooney, Ralspeed Ltd
A1 Hurstwood Court, Mercer Way, Shadsworh Business Park, Blackburn, BB1 2QU Tel: 01254 582345 Email: Web: are not responsible for the content of submitted or externally produced articles and images.
Click here to email PandCT about any errors or omissions contained within this article.
Send this page
To send this page to a colleague or friend,
fill in the email addresses below...
Your email address
Their email address:
Page to be sent: shownews.asp?ID=36107

Company gateway pages
for Ralspeed Ltd:
FREE Information on the products in this article
To request more information from this supplier,
fill in your email address below.
Your email address
Bookmark and Share
Product categories: Accelerometers | Actuators | Agitators | Analysers | Bearings | Compressors | Controllers | Conveyors | Drives | Enclosures | Flowmeters | Heat Exchangers | Motors | Pumps | Relays | Sensors | Transducers | Transmitters | Valves | Weighing
(c) Copyright 1999-2019 Process and Control Today Ltd  |  Reg. no 3733110  |  Email Editor  |  Email Webmaster  |  Sitemap  |  Privacy Policy