Sunday 15/12/2019

Bookmark and Share
Case Studies
  PandCT RSS Case Studies feed
Brakes for holding and parking of copper mine hoists feature precision control

13 September 2017

Twiflex, part of Altra Industrial Motion, a leading global supplier of power transmission components, provided parking brakes for use on mine hoists at the Nkana site of Mopani Copper Mines in Zambia. Nkana is one of the largest copper and cobalt mines in Africa, with four underground mines, as well as an open pit.

Leading mine hoist manufacturer FLSmidth worked with Twiflex and its South African distribution partner, Tritec Sintered Products, on this installation. FLSmidth supplied a double drum Blair Multi-Rope (BMR) rock winder and a single drum BMR man / materials winder to the Nkana project. The BMR winder is a variation on the double-drum winder and is used in extremely deep shafts as the second drums cable is used to balance the primary load. The drums on both winders are identical; each measuring 5.7 m in diameter, with two 1.8m wide rope compartments.

The double-drum BMR has a payload of 47.5 tonnes and operates at speeds up to 17.6 m/s in a 1,278 m deep shaft. A precision control system designed by FLSmidth is used to achieve synchronous braking of all the brake units.

Twiflex brakes are used for parking and holding each time the mine winders stop. In exceptional conditions (i.e. power failure), the brakes can be used to bring the load to rest whilst maintaining a maximum deceleration of 2.3 m/s2.

To meet the hoists high rubbing speeds and provide greater thermal capacity, Twiflex engineers designed a new large pad version (174,700 mm2 each pad) of its popular VMS3-SPS spring-applied, hydraulically-released brake, which is widely used on mine hoists around the world. Thermal capacity is a measure of the ability of the brake pad to absorb and dissipate heat. Known as the VMS3-VR the 16 off brakes (8 off on the fixed drum and 8 off on the clutched drum) operate on two 6,800mm diameter, 70 mm thick discs, producing a total braking torque of 12.2 MNm.

For this application, each VMS3-VR is rated to 240 kN braking force (µ=0.4) using a 2mm air gap. At this braking force, the rated fatigue life is over two million braking cycles. To assist with maintenance, Twiflex brakes incorporate a monitoring system to signal brake pad wear and loss of braking force. The VMS3-VR brakes also include Twiflex’s unique ‘parked off’ feature: meaning they can be adjusted under hydraulic pressure so that when pressure is removed there is no stored energy.

Twiflex has an in-house testing capability, comprising a climatic chamber which can simulate temperatures between -75 to +180 °C, as well as a fatigue room for brake cycling and an inertia test rig for dynamic stops.

“All Twiflex modular brakes are subject to a cycling test and pressure test before leaving the factory,” explains Steve Powell, product manager for Twiflex. “For mine hoists, all critical brake components undergo non-destructive testing. The main limitation for brake manufacturers is the friction material which needs to be carefully selected for the operating cycle.”

For more information, please contact:

Anthony George
Twiflex Limited
9 Briar Road
TW2 6RB 
Tel:  +44 20 8755 5611 
Web: are not responsible for the content of submitted or externally produced articles and images.
Click here to email PandCT about any errors or omissions contained within this article.
Send this page
To send this page to a colleague or friend,
fill in the email addresses below...
Your email address
Their email address:
Page to be sent: shownews.asp?ID=49435

Company gateway pages
for Twiflex Ltd:
FREE Information on the products in this article
To request more information from this supplier,
fill in your email address below.
Your email address
Bookmark and Share
Product categories: Accelerometers | Actuators | Agitators | Analysers | Bearings | Compressors | Controllers | Conveyors | Drives | Enclosures | Flowmeters | Heat Exchangers | Motors | Pumps | Relays | Sensors | Transducers | Transmitters | Valves | Weighing
(c) Copyright 1999-2019 Process and Control Today Ltd  |  Reg. no 3733110  |  Email Editor  |  Email Webmaster  |  Sitemap  |  Privacy Policy