Thursday 15/11/2018

Bookmark and Share
 
 
Editor's Comment
  PandCT RSS Editorial feed
Reduce waste and future-proof production with automatic product recovery

12 July 2018

By Matt Hale, International Sales & Marketing Director, HRS Heat Exchangers

It seems that everybody is talking about Industry 4.0. Whether you are reading an online publication, reading a magazine, visiting a trade show or talking to business consultants, it doesn’t take long for the latest manufacturing buzzwords of ‘Industry 4.0’, ‘fourth industrial revolution’, or ‘internet of things’ to be mentioned.

All three terms refer to the shift in industry towards autonomous production systems using not just pre-programmed machinery and robots, but machines which are controlled and monitored by computer-based algorithms, often using the internet to link controls and systems in different locations, sometimes known as ‘cyber-physical systems.’ While there is a lot of hype around Industry 4.0, there is no doubt that the general direction of travel in manufacturing is for the use of more autonomous systems.

This trend also presents a fantastic opportunity for businesses to tackle key challenges, such as increasing energy efficiency, improving working conditions, or minimising and preventing waste. For example, installing a system which automatically diverts residual product when it no longer meets specification can significantly reduce waste and improve cleaning processes.

The scale of residual food waste

When processing various, often viscous, food products a certain amount adheres to the inside surfaces of machinery and pipework. Some product may also be left behind upon completion of each production run. The scale of this problem is huge, with a 2010 European study suggesting that 4.1 million tonnes of food is lost during processing each year in the UK1, costing hundreds of thousands of pounds annually.

A combination of good design – to minimise the amount of product that remains behind or adheres to the surface – and cleaning systems can be used to overcome the issue. The three main techniques – physical ‘pigging systems’, water-based flushing, and forcing clean air through the system – all remove residual product as part of cleaning-in-place (CIP) procedures. Depending on the range of products handled and product complexity this may need to be carried out several times a day between production batches.

Regaining control

While all three of these recovery techniques have the ability to salvage residual product, inevitably, a certain amount is still lost as waste. However, by using inline monitoring equipment linked to a system designed to allow product which meets the specified parameters to be reworked, the amount of valuable product recovered from equipment such as pasteurisers and sterilisers can be maximised.

This technique works by using an inline instrument to measures changes in the physical or chemical properties of the product, such as concentration. This information is passed to a controller which determines whether to ‘keep’ or ‘discard’ that material based on pre-determined quality parameters.

This concept of feedback control is not new in automation. Every HRS pasteuriser or steriliser already has a temperature transmitter and a three-way valve installed after the holding tube. If for any reason the pasteurisation or sterilisation temperature (set point) is not maintained through the holding tube, the temperature transmitter sends a signal to the valve to return the product to the holding tank.

This same principle is now being applied to the HRS Product Recovery System. Rather than just measuring temperature, any suitable physical or chemical property can be continually monitored, such as Brix, pH, viscosity or density. The choice of which parameter is used depends on the nature of the product and the sensors that are available.

Recovery in practice

A line producing fruit juice may have a typical sugar level of 12 Brix. The concentration of the juice leaving the pasteuriser is monitored using a Brix meter, and any juice which falls below this level is diverted to waste. The line employs water flushing as part of its CIP systems. Traditionally, because it could not accurately be determined where the mixing zone between residual product and flushing water began, anything passing through the pasteuriser during this cleaning phase would have been discarded, including any perfectly good product left in the pasteuriser at the end of the production cycle. However, by monitoring the product concentration from the beginning of the flushing cycle, it is possible to send juice with a Brix level of 12 or higher to the next phase of production (such as packing), and only discard material which falls below this set parameter.

Another example involves a manufacturer of BBQ sauce. Assuming the company makes a profit of 40 pence per litre of sauce, even if 200 litres are lost per production line during cleaning cycles each day, that equates to a loss of £80 a day or £24,000 a year (assuming 300 days production). If the company has four lines then it is losing almost £100,000 worth of profit, not to mention the creation of around 68 tonnes of waste each year.

Benefitting pocket and planet

As well as increasing the amount of product which can be sold, reducing the amount of waste generated decreases disposal costs such as storage, transport and treatment. Alongside these financial benefits, the environmental footprint of the production line will also be improved, with more end product being obtained for the same effort – effectively lowering CO2e emissions per unit produced. Furthermore, cutting down the amount of product mixed in with the flushing or cleaning water means that the resulting waste stream is cleaner and will require less processing, further reducing financial and environmental costs.

As all HRS pasteurisers and sterilisers already include a three-way valve to allow for the diversion of out-of-specification product, the only real additional expense are the monitoring and control systems. With potential cost savings running into hundreds of thousands of pounds, such systems rapidly repay any additional capital expense. With manufacturers’ focus on Industry 4.0 now prompting them to reassess the efficiency of all their processes, it’s easy to see why Product Recovery Systems are increasingly being specified alongside both new and existing sterilisation and pasteurisation systems.

For more information, please contact:

HRS Heat Exchangers Ltd
HRS House
10-12 Caxton Way
Watford Business Park
Watford
Hertfordshire
WD18 8JY
Tel:  +44 (0)1923 232 335
Fax:  +44 (0)1923 230 266
Email: info@uk.hrs-he.com
Web:  www.hrs-heatexchangers.com
The editor
PandCT.com are not responsible for the content of submitted or externally produced articles and images.
Click here to email PandCT about any errors or omissions contained within this article.
     
Send this page
To send this page to a colleague or friend,
fill in the email addresses below...
Your email address
Their email address:
Page to be sent: shownews.asp?ID=51497

Company gateway pages
for HRS Heat Exchangers Ltd:
FREE Information on the products in this article
To request more information,
fill in your email address below.
Your email address
 
     
Bookmark and Share
Product categories: Accelerometers | Actuators | Agitators | Analysers | Bearings | Compressors | Controllers | Conveyors | Drives | Enclosures | Flowmeters | Heat Exchangers | Motors | Pumps | Relays | Sensors | Transducers | Transmitters | Valves | Weighing
(c) Copyright 1999-2018 Process and Control Today Ltd  |  Reg. no 3733110  |  Email Editor  |  Email Webmaster  |  Sitemap  |  Privacy Policy