Wednesday 22/8/2018

Bookmark and Share
 
 
Case Studies
  PandCT RSS Case Studies feed
Hurricane-force performance as new screen lives up to recommendations in Utah

6 August 2018

At a Utah facility that has seven wastewater treatment lagoons treating 1.5 MGD and over 300 acres of farm land, a new screen has immediately improved aerator reliability, with an added benefit of significantly improved system aesthetics.

Constructed in the early 80’s, the lagoons transitioned over the course of the next 20 years from facultative to aerobic lagoons, with the installation of surface-mounted aerators. Due to the increasing use and disposal of wet wipes (‘flushable’ or ‘non-flushable’), Ash Creek Special Service District regularly struggled with mechanical breakdowns in their lagoon aeration system. An accumulation of wipes and rags would become bound around the aerator drive shafts, reducing performance until the motor became completely bound, resulting in an over-amp fault. A grinder installed for the purpose of shredding the rags proved ineffective, because shredded rags and wipes recombined in the lagoon mixing areas and re-emerged as chords and ropes of the residual debris. Frustrated personnel at Ash Creek Special Service District (which serves the towns of Hurricane, La Verkin and Toquerville), were spending excessive amounts of time on maintenance, while aeration performance in the lagoons was regularly impaired.

District staff began a process of site visits to wastewater plants in the area, requesting feedback from system operators on their satisfaction with screening performance at their facility. Simultaneously, staff began identifying key requirements for the screening system that they would ultimately like to see implemented at the District’s facility.

These requirements included a very high capture efficiency, a full penetration cleaning mechanism to eliminate the possibility of screen blinding and a single integral screening/washer/compactor unit.

“We quizzed local engineers about perceived strengths of various screen types that they had seen implemented in facilities like ours”, reflected Mike Chandler, District Superintendent.

“That information, coupled with a strong endorsement from a neighbouring facility pointed us in the direction of the inclined basket screen, and more specifically, Lakeside’s Raptor Fine Screen”.

‘Reduced disposal costs’

Benefits of this screen include increased removal efficiency and low headloss - brought about by its cylindrical screenings basket, angled installation and screen bars of varied heights. Inorganic solids that can be harmful to downstream equipment are securely captured. The screen’s rotating rake teeth fully penetrate the cylindrical screen bars, positively removing debris and grease to prevent blinding or plugging. Also suitable for septage receiving, sludge, scum and grease trap applications, the screen’s heavy-duty design provides durability and long life in the most severe conditions. Captured screenings are compacted, dewatered and washed free of most organics to approximately 40 percent solids. Volume is reduced by 50 percent and weight by 67 percent, thus reducing disposal costs.

Together, Ash Creek’s personnel worked with Lakeside’s Jim Aitkenhead and his team of engineers to design an influent receiving box and control structure that could be easily provided by a local supplier of pre-cast concrete structures.

One month ahead of the arrival of the all-stainless steel Lakeside Raptor Screen, the team at Ash Creek installed the control structure and screening channel, also erecting an electrical building and non-potable water air-gap tank for the screening washdown nozzles – as well as installing a screening structure washdown hose bib. Ash Creek’s operators then later installed the (supplied) fully assembled screen and worked closely alongside Lakeside during final commissioning.

When the upstream water level rises to a high level set point, the Raptor Screen’s rake arm begins to rotate for removal of the captured material. After the rake arm makes a complete revolution, material falls into a collection trough. For complete cleaning, the rake arm reverses direction at the top of the screenings basket and passes through a hinged cleaning comb. The debris is removed from the collection trough by a central screw conveyor. The conveyed material travels up the inclined transport tube where the material is washed, compacted, and dewatered prior to being discharged into a debris container.

Made in the USA, the Raptor Screen’s hinged structural support allows the unit to pivot out of channel for inspection at floor level, whilst its simple drive assembly also makes service easy and further reduces maintenance costs.

‘Trouble-free’

“We made a minor adjustment on the new screen’s control floats”, continued Mike Chandler, “and the Lakeside Raptor has run totally trouble-free. The amount of rags and debris it removes has surprised us all here at Ash Creek. The washed and compacted screenings are also very low on odor, which has been a bonus”.

He concluded: “Overall, we can see what a tough and well-designed piece of equipment this is from Lakeside, who have clearly earned the recommendations we received from happy plant operators”.

For more information, please contact:

Lakeside Equipment Corporation
1022 E. Devon
P.O. Box 8448
Bartlett
IL 60103
Tel:  +1 630.837.5640
Email: sales@lakeside-equipment.com
Web:  www.lakeside-equipment.com/
PandCT.com are not responsible for the content of submitted or externally produced articles and images.
Click here to email PandCT about any errors or omissions contained within this article.
     
Send this page
To send this page to a colleague or friend,
fill in the email addresses below...
Your email address
Their email address:
Page to be sent: shownews.asp?ID=51666

Company gateway pages
for Lakeside Equipment Corporation:
FREE Information on the products in this article
To request more information from this supplier,
fill in your email address below.
Your email address
 
     
Bookmark and Share
Product categories: Accelerometers | Actuators | Agitators | Analysers | Bearings | Compressors | Controllers | Conveyors | Drives | Enclosures | Flowmeters | Heat Exchangers | Motors | Pumps | Relays | Sensors | Transducers | Transmitters | Valves | Weighing
(c) Copyright 1999-2018 Process and Control Today Ltd  |  Reg. no 3733110  |  Email Editor  |  Email Webmaster  |  Sitemap  |  Privacy Policy