Thursday 17/10/2019

Bookmark and Share
 
 
Daily News
  PandCT RSS Daily News feed
ERIKS SHARES TOP TIPS TO KEEP YOUR BELTS IN BUSINESS

3 May 2019

Insight from ERIKS, the UK’s leading industrial services partner, estimates that incorrectly installing and maintaining belt drives accounts for 98 per cent of premature failures, leading to downtime and lost production. With this in mind, Gary Price, Power Transmission Regional Product Group Manager, at ERIKS highlights some tips that can extend the life of belt drives and pulleys, increasing their reliability, reducing their total cost of ownership, and minimising the chances of downtime.

Consider the environment

To avoid potential risks associated with belt failure and downtime, it is important to select a belt type appropriate for the application at hand. In addition to thinking about how much power will be absorbed, required running speed and the service duty of the application, the operating conditions should also be considered.

For example, if the process is subjected to harsh climates or contaminants – whether that be extremes in temperatures, condensation, dust or corrosive chemicals to name a few - make sure the specified belt can resist the challenges.

Tighten it right

With belt tension critical to efficient performance, more accurate belt tensioning can increase belt life by up to 50% and just five per cent under or over tensioning can cause premature failure. Tension values are scientifically calculated according to variables such as the type of drive, absorbed power, how much pressure is exerted on the belt, how much movement it deflects, the number of belts installed and pulley sizes, so tensioning a belt based on the traditional method of ‘twisting a belt half a turn’ will not be adequate.

If a belt is under tensioned, it will slip in the pulley. This generates heat and increases the chances of secondary curing. Conversely, an over-tensioned belt introduces more wear in related mechanical components such as bearings and motor shaft.

To ensure belts are tensioned correctly, gauges should be used so that they are tightened to the manufacturers recommended values. Remember, friction belts need to be re-tensioned 3-4 times during their average three-year lifetime.

Get slack

Best practice dictates that you slacken the tension when fitting the belt - never lever it on with a screwdriver or crowbar, as this risks damaging the belt and / or the drive. Always check the amount of belt deflection at installation, and that it has been aligned correctly with a laser tool, not by eye.

Replace worn pulleys

It is estimated that 50 per cent of new belts are fitted to worn pulleys – wasting energy and compromising the lifespan of new belts by up to half. Replacing a worn belt but leaving a worn pulley in place will do little to restore the efficiency of a drive, and the belt will have a far shorter life cycle than it should. For optimum performance, pulleys need changing at every third belt change.

Time it well

Although friction belts are the traditional choice, timing belts have several advantages in many applications. They never need re-tensioning and maintain 98-99% efficiency for their whole three-year design life. Therefore, it can make financial sense to choose timing rather than friction belts for existing and new applications.

If you choose a timing belt you will also need to replace the pulleys – but that will lead to additional gains. For example, one timing belt can deliver the same power as multiple friction belt setups, reducing pulley sizes and space. In most cases the reduced maintenance costs, reduced downtime and lower energy requirements should provide payback in just 3-4 months.

For more information, please visit: www.eriks.co.uk
PandCT.com are not responsible for the content of submitted or externally produced articles and images.
Click here to email PandCT about any errors or omissions contained within this article.
     
Send this page
To send this page to a colleague or friend,
fill in the email addresses below...
Your email address
Their email address:
Page to be sent: shownews.asp?ID=53428

Company gateway pages
for ERIKS UK:
FREE Information on the products in this article
To request more information,
fill in your email address below.
Your email address
 
     
Bookmark and Share
Product categories: Accelerometers | Actuators | Agitators | Analysers | Bearings | Compressors | Controllers | Conveyors | Drives | Enclosures | Flowmeters | Heat Exchangers | Motors | Pumps | Relays | Sensors | Transducers | Transmitters | Valves | Weighing
(c) Copyright 1999-2019 Process and Control Today Ltd  |  Reg. no 3733110  |  Email Editor  |  Email Webmaster  |  Sitemap  |  Privacy Policy